#ifndef __SENSOR_TBL_H__
#define __SENSOR_TBL_H__

#include <stdint.h>
#include "bmc_conf.h"

/**
 ** @brief HAL Error code definitions
 ***/
typedef enum
{
    /* HAL Error codes  */
    HAL_ERR_NONE,           /* No error */
    HAL_ERR_READ,           /* Error in reading device */
    HAL_ERR_WRITE,          /* Error in writing to device*/
    HAL_ERR_FUNC_NOT_SUPPORTED,     /* Function called is not supported */

} hal_status_codes_e;

/**
 ** @brief HAL Supported Hardware functions
 ***/
typedef enum
{
    HAL_DEVICE_READ,        /* General Read function */
    HAL_DEVICE_WRITE,       /* General Write function */

    /* Special I2C  functions  */
    HAL_I2C_READ_REG,       /* Read I2C register */
    HAL_I2C_READ_WRITE,     /* Read/Write I2C */

    /* Special GPIO  functions  */
    HAL_SET_GPIO_DIR,       /* GPIO Set direction */
    HAL_GET_GPIO_DIR,       /* GPIO Get direction */
    HAL_SET_GPIO_POL,       /* GPIO Set Polarity */
    HAL_GET_GPIO_POL,       /* GPIO Get Polarity */
    HAL_SET_GPIO_OUTPUT_REG,       /* GPIO Set output data register */

} hal_func_codes_e;


/**
 ** @brief This structure necessary hardware information to access any device
 ***/
typedef struct
{
    hal_status_codes_e  status_code;    /* HAL api's status codes */
    hal_func_codes_e    func;           /* Hardware function */

    union {
        uint8_t              *pbyte;         /* All HAL apis return data
                                        in bytes using this pointer */
        uint16_t             *pword;         /* All HAL apis return data accesed
                                        in words using this pointer */
    };

    int                 read_len;       /* bytes to read */
    uint8_t             *pwrite_buf;    /* All HAL apis write data
                                        from this buffer */
    int                 write_len;      /* bytes to write */

//    hal_dev_properties_t dev_prop;      /* Device properties information */
//    hal_dev_type_e      dev_type;       /* Type of the device */
//
//    hal_i2c_t           i2c;            /* Hold I2C information */
//    hal_gpio_t          gpio;           /* Hold GPIO information */
//    hal_mmap_t          mmap;           /* Hold memory mapped information */
//    hal_adc_t           adc;            /* Hold ADC information */
//
//    hal_fanpwm_t     fan; 	/* Hold FanPwm information Added by winston for fanpwm */
//    hal_peci_t  peci;            /* Hold PECI information Added by winston for peci */
//    hal_lpcuart_t lpcuart;            /* Hold LPCUART information Added by jcchiu for lpcuart */
//    hal_intsensor_t intsensor;     /* Hold Interrupt Sensor information */
//    hal_nmsensor_t nmsensor;     /* Hold Interrupt Sensor information */
} hal_t;

typedef enum {
	MonitorOnStandby,
	NotMonitorOnStandby
}monit_sta_t;

/**
 ** @brief HAL read/write/init function type definition
 ***/
typedef int (*phal_hndlr_t) (hal_t *phal);

/**
 ** @brief HAL Device Table
 ***/
typedef struct
{
        uint8_t         sensor_number;
	uint8_t		poweron_delay;	//scan this sensor after poweron_delay seconds, when bmc power on.
	uint8_t		reset_delay;	//scan this sensor after reset_delay senconds, when cpu reset.
	uint8_t		monitor_interval;	//Monitoring this sensor every monitor_interval seconds.
	monit_sta_t  	monitor_state;		//whether monitoring this sensor when standby.			
        phal_hndlr_t 	device_read;
        phal_hndlr_t 	device_write;
        phal_hndlr_t 	device_init;
} sensor_tbl_t;


#endif /* __SENSOR_TBL_H__ */